Skip to content

Expansion Joint Design and Application Training Course

Size, specify and anchor metallic bellows and fabric joints so piping and ducting absorb movement without overloading nozzles or anchors.

This 1-week course has 25 dates from November 2026 to November 2027 in 24 cities and live online. The next session runs 30 November – 4 December 2026 in Amsterdam. Fees per participant run from 4,000 £ (Cairo) to 9,500 £ (New York) in a classroom, and from 2,900 £ live online.

See dates and book Download brochure (PDF) Training for your team

Duration
1 Week
Next start
Amsterdam
Scheduled dates
25
Classroom cities
24
Classroom fee from
4,000 £
Online fee from
2,900 £

When and where does this course run?

Showing 1–20 of 25 dates

November 2026

December 2026

January 2027

February 2027

March 2027

April 2027

May 2027

June 2027

July 2027

August 2027

Can’t find a suitable date? Tell us what you need.

What does this course cover?

Expansion Joint Design and Application is a 1-week training course for piping, mechanical and stress engineers who select, specify and install bellows and fabric joints, ending in a joint selection and anchoring dossier. Thermal growth, vibration and settlement in plant pipework and ducting must be absorbed without overloading nozzles or anchors, so a well-chosen joint protects rotating equipment and uptime. Jupiter Prime Training shapes this course around that discipline.

Why Expansion Joint Design and Application Matters Now

Plants are running hotter cycles, adding heat recovery ducting and tying new units into older pipe racks, and each change alters the movements a line must absorb. Operators expect longer intervals between shutdowns. A joint sized for the wrong movement, or installed without proper guides, can squirm, fatigue or transfer pressure thrust into a pump casing. The course rests on recognised bellows fatigue and squirm relationships, pipe stress analysis practice and manufacturer movement data.

Who Gains Most from Expansion Joint Design and Application

  • Engineers responsible for routing pipework and deciding where flexibility is needed
  • Specialists who run stress models and set anchor and guide loads
  • Engineers who write purchase specifications and review vendor bellows calculations
  • Maintenance engineers who inspect, replace and troubleshoot flexible elements in service
  • Duct and flue gas system engineers handling large low-pressure movements

A design or maintenance group gains most when its layout, stress and inspection engineers attend together and agree one set of movement and anchoring rules.

Expansion Joint Design and Application Capabilities

Participants move from movement calculations to a specified, anchored and inspectable bellows or fabric joint arrangement.

  • Calculate axial, lateral and angular movements from thermal and settlement cases — line routing decisions
  • Specify bellows convolution, ply and material for the pressure and temperature envelope — purchase specifications
  • Design main and intermediate anchors and guides against pressure thrust — civil and support steel teams
  • Weigh untied, tied, hinged, gimbal and pressure-balanced arrangements — layout and cost choices
  • Assess fabric joint layers for flue gas temperature and chemistry — duct system owners
  • Build installation, pre-set and inspection checklists — construction and maintenance crews

Key Expansion Joint Design and Application Terms

  • Bellows — a thin-walled convoluted cylinder that flexes to absorb movement while containing pressure.
  • Pressure thrust — the axial force equal to pressure times bellows effective area, which anchors or tie rods must resist.
  • Squirm — lateral instability of a bellows under internal pressure, where convolutions shift sideways and lose their shape.
  • Spring rate — the force needed to move a bellows one unit of displacement, passed to adjoining nozzles and anchors.
  • Cold pull — pre-setting a joint during installation so operating movement is shared either side of neutral length.
  • Fabric joint — a flexible connector of layered cloth, insulation and gas seal used on ducts with large movements.

Expansion Joint Design and Application Day by Day

Day 1: Movement Sources and Flexibility Options

  • Thermal Growth Calculation — Sizing Movements Across Operating Cases
  • Pipe Loops Versus Flexible Elements — Choosing Space, Cost and Reliability
  • Settlement, Vibration and Wind Inputs — Completing the Movement Envelope
  • Nozzle Load Limits of Pumps and Compressors — Setting Flexibility Targets
  • Line Classification Sheet — Deciding Which Lines Need Joints

Day 2: Metallic Bellows Design

  • Convolution Geometry and Ply Count — Balancing Pressure Capacity and Flexibility
  • Bellows Material Selection — Matching Alloys to Corrosion and Temperature
  • Fatigue Cycle Life Estimation — Judging Margin for Start-Up Cycles
  • Column and In-Plane Squirm Checks — Confirming Stability Under Test Pressure
  • Vendor Bellows Calculation Review — Accepting or Querying Supplier Data

Day 3: Thrust, Anchors and Restrained Arrangements

  • Effective Area and Pressure Thrust — Sizing Main Anchor Loads
  • Intermediate Anchors and Guide Spacing — Preventing Buckling of the Line
  • Tied, Hinged and Gimbal Assemblies — Containing Thrust Within the Joint
  • Pressure-Balanced and Universal Joints — Protecting Sensitive Equipment Nozzles
  • Stress Model Representation of Joints — Feeding Spring Rates Into Analysis

Day 4: Fabric Joints, Installation and Failure Prevention

  • Fabric Layer Build-Up for Flue Gas Ducts — Selecting Seal and Insulation
  • Pre-Set, Cold Pull and Shipping Bars — Controlling Installation Errors
  • Hydrotest Precautions for Bellows — Avoiding Squirm During Pressure Tests
  • Failure Modes From Chlorides, Erosion and Torsion — Ranking Root Causes
  • In-Service Inspection Criteria — Deciding Repair, Replace or Monitor

Day 5: Practising the Joint Selection and Anchoring Dossier

  • Movement Envelope for a Case Line — Applying Day One Calculations
  • Bellows Sizing and Squirm Check — Applying Day Two Methods
  • Anchor and Guide Layout — Applying Day Three Thrust Rules
  • Purchase Data Sheet and Installation Checklist — Preparing Vendor Enquiry
  • Joint Selection and Anchoring Dossier — Presenting the Final Arrangement

Applying Expansion Joint Design and Application After the Course

  • Audit existing bellows on a hot line against movement, guide spacing and squirm checks taught on the course.
  • Rewrite the site purchase data sheet for metallic and fabric joints with movement, thrust and pre-set fields.

Expansion Joint Design and Application Questions (FAQ)

What is expansion joint design and application, and why does it matter now?

It is the practice of sizing, selecting and anchoring flexible elements that absorb pipe and duct movement. It matters now because hotter cycles, retrofits and longer run lengths raise the loads on nozzles, anchors and bellows.

Which roles gain most from expansion joint design and application training?

Piping layout, stress and mechanical engineers gain most. Maintenance and inspection engineers who replace bellows and duct engineers who handle fabric joints also gain.

How does expansion joint design and application differ from a general pipe stress course?

It focuses on the flexible element itself. A general pipe stress course models whole systems, while this one goes deep into bellows geometry, thrust restraint, squirm, fabric layers, installation pre-set and failure causes of joints.

What do you bring back from expansion joint design and application training?

You bring back a worked dossier for a real line: its movements, chosen joint type, bellows checks, anchor and guide loads, purchase data sheet and installation checklist.

Expansion Joint Design and Application: The Way Forward

The joint selection and anchoring dossier first informs whether a line receives a loop or a flexible element, and which restraint type it needs. Layout, stress and procurement engineers use it to brief vendors. After its first use, revisit the fatigue cycle assumptions against actual start-up records, since operating patterns often differ from design cases.

Questions about dates, fees and booking

When does this course next run?

The next session runs 30 November – 4 December 2026 in Amsterdam. It is one of 25 dates scheduled up to November 2027.

Where is this course held?

In a classroom in 24 cities: Amsterdam, Muscat, Rome, Manama, London, Amman, Paris, Singapore, and more. It is also scheduled as live online sessions.

Can I attend this course online?

Yes. One date is scheduled as a live online session: 10 – 14 October 2027, from 2,900 £ per participant.

How long is the course?

1 Week. Each date shows its start and end dates.

How much does the course cost?

Fees per participant run from 4,000 £ (Cairo) to 9,500 £ (New York) in a classroom, and from 2,900 £ live online. Each date shows its own fee.

Is there a brochure for this course?

How do I book a place?

Choose a date above and select Register, or send us an enquiry.

Can this course be run for our team?

Yes. Tell us the number of participants and your preferred dates and city through our training request form.

More ways to train