Skip to content

Route-Based Vibration Monitoring and Fault Diagnosis Training Course

Route-based vibration monitoring and fault diagnosis for technicians who collect routes, read FFT spectra and make sound first-line fault calls.

This 1-week course has 25 dates from November 2026 to November 2027 in 24 cities and live online. The next session runs 23 – 27 November 2026 in London. Fees per participant run from 4,000 £ (Cairo) to 9,500 £ (New York) in a classroom, and from 2,900 £ live online.

See dates and book Download brochure (PDF) Training for your team

Duration
1 Week
Next start
London
Scheduled dates
25
Classroom cities
24
Classroom fee from
4,000 £
Online fee from
2,900 £

When and where does this course run?

Showing 1–20 of 25 dates

November 2026

December 2026

January 2027

February 2027

March 2027

April 2027

May 2027

June 2027

July 2027

August 2027

September 2027

Can’t find a suitable date? Tell us what you need.

What does this course cover?

Route-Based Vibration Monitoring and Fault Diagnosis is a 1-week training course for condition monitoring technicians and reliability engineers who collect route readings and give first fault verdicts, ending with a route fault findings sheet for one plant area. Unread spectra still let rotating failures arrive unannounced. Jupiter Prime Training delivers this course for practitioners who walk the plant.

Why Route-Based Vibration Monitoring and Fault Diagnosis Matters Now

Three forces shape route-based work on rotating plant today. Data collectors and wireless sensors now gather more readings than sites can read. Experienced analysts are retiring, leaving technicians to make first calls, and operations expect warnings that fit planned shutdowns. A site that reads its routes well catches bearing wear and misalignment weeks ahead; one that does not pays for secondary damage and lost output. The course rests on accepted practice for machine vibration measurement and evaluation, described in general terms.

Who Gains Most from Route-Based Vibration Monitoring and Fault Diagnosis

  • Technicians who carry the data collector and gather readings on scheduled machine routes
  • Reliability engineers who set measurement points, intervals and alarm levels for rotating plant
  • Mechanical craft supervisors who act on vibration findings when planning corrective jobs
  • Predictive maintenance coordinators who maintain route databases and trend histories
  • Rotating equipment specialists who confirm or escalate a first-line fault call

A site crew gains most when its route collectors and the engineer who signs off their findings attend together.

Route-Based Vibration Monitoring and Fault Diagnosis Capabilities

Participants move from a correct reading to a named fault and a clear next action.

  • Specify transducer type, mounting and measurement direction for each route point — the route designer
  • Build a collection route — the planning scheduler
  • Apply FFT spectrum settings that resolve the fault frequencies of a given machine — the analyst sign-off
  • Assess spectra and waveforms for imbalance, misalignment, looseness and bearing defects — the repair decision
  • Calculate bearing defect frequencies from geometry and running speed — the bearing replacement call
  • Communicate a severity grading and recommended action — the maintenance planner

Key Route-Based Vibration Monitoring and Fault Diagnosis Terms

  • Accelerometer — a transducer that converts surface acceleration into an electrical signal.
  • FFT spectrum — a plot showing vibration amplitude at each frequency.
  • Running speed (1X) — the shaft rotation frequency, the reference against which most fault frequencies are expressed.
  • Time waveform — the raw vibration signal over time, useful for spotting impacts, truncation and beating.
  • Bearing defect frequencies — the characteristic frequencies generated when the outer race, inner race, rolling elements or cage are damaged.
  • Alarm band — a frequency range with an amplitude limit that flags a reading for attention when exceeded.

Route-Based Vibration Monitoring and Fault Diagnosis Day by Day

Day 1: Measurement Points and Transducers

  • Velocity, Acceleration and Displacement Units — Choosing the Quantity for Each Machine
  • Accelerometer Mounting Methods — Repeatable Readings Versus Collection Speed
  • Horizontal, Vertical and Axial Directions — Where Faults Show Themselves First
  • Point Naming and Machine Asset Hierarchy — Traceable Trends in the Route Database
  • Overall Level Readings — When a Single Number Is Enough

Day 2: Building and Running the Route

  • Machine Criticality Ranking — Setting Collection Intervals Across the Plant
  • Route Sequence and Walking Order — Collection Time and Operating Conditions
  • Data Collector Setup and Downloads — Clean Records for Later Diagnosis
  • Operating Notes and Load Conditions — Comparing Readings Like for Like
  • Baseline Readings on New or Repaired Machines — Reference for Future Trends

Day 3: Reading Spectra and Waveforms

  • FFT Resolution, Lines and Maximum Frequency — Separating Close Fault Peaks
  • Averaging and Windowing Choices — Stable Spectra on Variable Machines
  • Harmonics and Sidebands — Linking Peaks to Shaft and Gear Sources
  • Time Waveform Patterns — Impacts, Rubs and Beating Identified
  • Trend Plots and Alarm Bands — Deciding When a Reading Needs Attention

Day 4: First-Line Fault Diagnosis

  • Imbalance Signatures at 1X Radial — Balancing Request or Further Checks
  • Misalignment Patterns with Axial 2X — Coupling Alignment Job Raised
  • Structural and Rotating Looseness — Foundation Repair or Component Fit
  • Bearing Defect Frequency Calculation — Stage of Wear and Replacement Timing
  • Lubrication and Resonance Clues — Ruling Out False Fault Calls

Day 5: Practising the Route Fault Findings Sheet

  • Route Data Set Review — Applying Day 2 Collection Records to a Live Case
  • Spectrum Reading Drill — Applying Day 3 Settings to Pump and Fan Data
  • Fault Verdict Exercise — Applying Day 4 Signatures to Mixed Faults
  • Severity Grading and Action Wording — Handover to Maintenance Planning
  • Route Fault Findings Sheet — Completed for One Plant Area

Applying Route-Based Vibration Monitoring and Fault Diagnosis After the Course

  • Re-walk one existing route, correcting point locations, directions and intervals against the criticality ranking taught
  • Run a monthly spectrum review with the crew, grading each alarm with the fault signatures and severity wording practised

Route-Based Vibration Monitoring and Fault Diagnosis Questions (FAQ)

What is route-based vibration monitoring and fault diagnosis, and why does it matter now?

It is the practice of collecting vibration readings on planned machine routes and reading them to name likely faults. It matters now because sites gather more data than ever and fewer analysts remain to read it.

Which roles gain most from route-based vibration monitoring and fault diagnosis?

Route collectors and reliability engineers gain most. Technicians learn to take repeatable readings and give a first verdict, while engineers learn to design routes and alarm bands.

How does route-based vibration monitoring and fault diagnosis differ from an advanced vibration analysis course?

It focuses on route design, data collection and first-line fault calls over one week. A longer advanced analysis course covers phase, gearboxes and transients for specialists.

What do you bring back from route-based vibration monitoring and fault diagnosis?

You bring back a route fault findings sheet for one plant area, graded by severity with recommended actions. You also return with a tested way of reading spectra for your crew.

Route-Based Vibration Monitoring and Fault Diagnosis: The Way Forward

The route fault findings sheet lists each machine on one route, its likely fault and a graded action. Its first use is deciding which repairs enter the next planned shutdown. Planners and supervisors read it. After its first cycle, revisit alarm bands and intervals, since early findings show which machines need closer watching.

Questions about dates, fees and booking

When does this course next run?

The next session runs 23 – 27 November 2026 in London. It is one of 25 dates scheduled up to November 2027.

Where is this course held?

In a classroom in 24 cities: London, Vienna, Madrid, Casablanca, Kuala Lumpur, Sharm El-Sheikh, Amman, Barcelona, and more. It is also scheduled as live online sessions.

Can I attend this course online?

Yes. One date is scheduled as a live online session: 2 – 6 May 2027, from 2,900 £ per participant.

How long is the course?

1 Week. Each date shows its start and end dates.

How much does the course cost?

Fees per participant run from 4,000 £ (Cairo) to 9,500 £ (New York) in a classroom, and from 2,900 £ live online. Each date shows its own fee.

Is there a brochure for this course?

How do I book a place?

Choose a date above and select Register, or send us an enquiry.

Can this course be run for our team?

Yes. Tell us the number of participants and your preferred dates and city through our training request form.

More ways to train