Skip to content

Sucker Rod and Progressing Cavity Pump Lift Training Course

Design, diagnose and extend run life of beam pumps and PCPs, from rod string loads and dynamometer cards to stator choice, for production engineers.

This 1-week course has 25 dates from November 2026 to November 2027 in 24 cities and live online. The next session runs 30 November – 4 December 2026 in London. Fees per participant run from 4,000 £ (Cairo) to 9,500 £ (New York) in a classroom, and from 2,900 £ live online.

See dates and book Download brochure (PDF) Training for your team

Duration
1 Week
Next start
London
Scheduled dates
25
Classroom cities
24
Classroom fee from
4,000 £
Online fee from
2,900 £

When and where does this course run?

Showing 1–20 of 25 dates

November 2026

December 2026

January 2027

March 2027

April 2027

May 2027

June 2027

July 2027

August 2027

September 2027

October 2027

Can’t find a suitable date? Tell us what you need.

What does this course cover?

Sucker Rod and Progressing Cavity Pump Lift is a 1-week training course for production and petroleum engineers who run rod-driven wells, and each participant leaves with a Rod Lift Run-Life Improvement Plan for a group of wells. Mature fields now depend on rod-driven pumps for a growing share of output, and each early rod or stator failure costs a workover. Jupiter Prime Training offers this course on Sucker Rod and Progressing Cavity Pump Lift.

Why Sucker Rod and Progressing Cavity Pump Lift Matters Now

Three pressures shape rod-driven lift today: rising water cut and declining reservoir pressure in older fields, heavier and sandier crude that punishes pumps, and fewer experienced staff who read cards. An operator that sizes rod strings well and watches pump fillage stretches the interval between workovers, while one that reacts only to failures spends its budget on rigs. The course rests on the wave-equation model for rod loads, the modified Goodman diagram for rod fatigue and inflow performance relationship (IPR) curves.

Who Gains Most from Sucker Rod and Progressing Cavity Pump Lift

  • Engineers who select pumping units, rod tapers and downhole pumps
  • Surveillance staff who read dynamometer cards and pump-off controller trends
  • Workover planners who decide when a failed well justifies a rig
  • Field leads who adjust stroke length, speed and rotor spacing
  • Failure analysts who inspect pulled rods, couplings, rotors and stators

Asset groups sending engineers and surveillance staff together gain most, since design and daily settings then share one diagnosis.

Sucker Rod and Progressing Cavity Pump Lift Capabilities

Participants practise moving from a downhole card or torque trend to a specific change at the wellhead.

  • Design a tapered rod string and check its loading on the Goodman diagram — well design approval
  • Interpret surface and downhole dynamometer cards — daily surveillance
  • Specify a progressing cavity pump geometry, elastomer and drive head — procurement and design
  • Calculate pump displacement, fillage and volumetric efficiency — production target setting
  • Apply teardown evidence to classify rod, tubing and stator failures — workover and supplier decisions
  • Weigh rod pump, progressing cavity pump and electric submersible pump options — lift selection reviews

Key Sucker Rod and Progressing Cavity Pump Lift Terms

  • Dynamometer card — a plot of polished rod load against position over one stroke.
  • Pump fillage — the share of the pump barrel filled with liquid on each upstroke.
  • Rod taper — a string built from sections of different rod diameters so stress stays within allowable limits.
  • Rotor and stator — the steel helix and elastomer-lined housing that form the sealed cavities of a progressing cavity pump.
  • Elastomer swell — volume growth of the stator rubber in contact with aromatics, gas or heat.
  • Mean time between failures — the average producing time of a well between pump-related workovers, the main run-life measure.

Sucker Rod and Progressing Cavity Pump Lift Day by Day

Day 1: Well Inflow and the Choice of Rod-Driven Lift

  • Inflow Performance Relationship Curves — Setting Realistic Drawdown Targets
  • Lift Method Screening Matrix — Rod Pump, PCP or Submersible Pump
  • Fluid Properties and Sand Content — Constraints on Pump Selection
  • Run-Life Economics — Workover Cost Against Deferred Production
  • Field Cases From Heavy Oil and Waterflood Assets — Lessons

Day 2: Beam Pumping Unit and Rod String Design

  • Pumping Unit Geometry and Gearbox Torque — Sizing and Counterbalance
  • Wave-Equation Load Prediction — Peak and Minimum Polished Rod Loads
  • Tapered Rod String Design — Goodman Diagram Stress Checks
  • Downhole Pump Types and Clearances — Matching Barrel to Fluid
  • Gas Separation at the Pump Intake — Anchor and Seating Depth

Day 3: Progressing Cavity Pump Design and Operation

  • Rotor and Stator Geometry — Displacement, Lift Capacity and Stages
  • Elastomer Selection and Swell Testing — Compatibility With Produced Fluids
  • Surface Drive Head and Torque Limits — Backspin and Rod Torsion
  • Rotor Spacing and Speed Control — Interference Fit and Wear
  • Sand and Viscous Crude Handling — Settings for Abrasive Wells

Day 4: Surveillance, Diagnostics and Failure Analysis

  • Surface and Downhole Dynamometer Card Patterns — Fault Recognition
  • Pump-Off Controller Logic — Idle Time and Stroke Rate Decisions
  • Fluid Level Shots and Torque Trends — Confirming Pump Condition
  • Rod, Coupling and Tubing Teardown Grading — Root Cause Classification
  • Corrosion and Wear Mitigation — Inhibitor Treatment and Rod Guides

Day 5: Practising the Rod Lift Run-Life Improvement Plan

  • Well Group Failure Ranking Using Mean Time Between Failures — Priority Wells
  • Redesign Exercise for a Rod Pump Well With Gas Interference — Corrective Settings
  • Redesign Exercise for a Sandy PCP Well — Elastomer and Speed Choices
  • Lift Conversion Case Review — When to Change Lift Method
  • Rod Lift Run-Life Improvement Plan — Final Presentation and Peer Challenge

Applying Sucker Rod and Progressing Cavity Pump Lift After the Course

  • Review dynamometer cards for the worst-performing rod pump wells and adjust pump-off settings where fillage is poor.
  • Set up teardown grading for every pulled PCP and rod string so failure causes are recorded consistently.

Sucker Rod and Progressing Cavity Pump Lift Questions (FAQ)

What is Sucker Rod and Progressing Cavity Pump Lift and why does it matter now?

It is the use of rod-driven downhole pumps, reciprocating or rotating, to lift oil from wells that no longer flow. It matters now because mature fields rely on it.

Which roles gain most from Sucker Rod and Progressing Cavity Pump Lift?

Production and petroleum engineers gain most, together with surveillance staff, workover planners and failure analysts.

How does Sucker Rod and Progressing Cavity Pump Lift differ from an electric submersible pump course?

It concentrates on rod-driven pumps powered from surface, not on downhole motor-driven pumps. Submersible pump courses cover cables, motors and drives; this one covers pumping units, rod strings, stators and card diagnostics.

What do you bring back from Sucker Rod and Progressing Cavity Pump Lift?

You bring back a Rod Lift Run-Life Improvement Plan for your own well group, with failure rankings and redesigned settings.

Sucker Rod and Progressing Cavity Pump Lift: The Way Forward

The Rod Lift Run-Life Improvement Plan first informs which wells receive redesign before their next failure. Production engineers, surveillance staff and workover planners use it to schedule interventions and order rods, pumps and stators. After first use, compare the predicted run-life gains with actual failure intervals to see which design assumptions held in the field.

Questions about dates, fees and booking

When does this course next run?

The next session runs 30 November – 4 December 2026 in London. It is one of 25 dates scheduled up to November 2027.

Where is this course held?

In a classroom in 24 cities: London, Madrid, Munich, Dubai, Manama, Muscat, Cairo, Casablanca, and more. It is also scheduled as live online sessions.

Can I attend this course online?

Yes. One date is scheduled as a live online session: 31 October – 4 November 2027, from 2,900 £ per participant.

How long is the course?

1 Week. Each date shows its start and end dates.

How much does the course cost?

Fees per participant run from 4,000 £ (Cairo) to 9,500 £ (New York) in a classroom, and from 2,900 £ live online. Each date shows its own fee.

Is there a brochure for this course?

How do I book a place?

Choose a date above and select Register, or send us an enquiry.

Can this course be run for our team?

Yes. Tell us the number of participants and your preferred dates and city through our training request form.

More ways to train