Bottom Hole Assembly Design and Directional Tendency Training Course
Drilling engineers and rig supervisors learn to predict build, drop and walk, match bits to assemblies and cut failed runs through fatigue control.
This 1-week course has 25 dates from November 2026 to November 2027 in 24 cities and live online. The next session runs 30 November – 4 December 2026 in London. Fees per participant run from 4,000 £ (Cairo) to 9,500 £ (New York) in a classroom, and from 2,900 £ live online.
See dates and book Download brochure (PDF) Training for your team
- Duration
- 1 Week
- Next start
- London
- Scheduled dates
- 25
- Classroom cities
- 24
- Classroom fee from
- 4,000 £
- Online fee from
- 2,900 £
When and where does this course run?
Showing 1–20 of 25 dates
November 2026
January 2027
February 2027
March 2027
April 2027
May 2027
June 2027
August 2027
September 2027
Can’t find a suitable date? Tell us what you need.
What does this course cover?
Bottom Hole Assembly Design and Directional Tendency is a 1-week training course for drilling engineers and rig-site supervisors who select and run BHAs, and it ends with a BHA Selection and Tendency Sheet for a planned hole section. Tighter well paths, longer laterals and costly trips make every BHA choice a direct lever on well time and tool failures. Jupiter Prime Training presents it as a design discipline.
Why Bottom Hole Assembly Design Matters Now
Three forces shape BHA design today: well profiles with more build, turn and extended reach; rotary steerable and motor systems that raise the cost of each failed run; and operators who judge drilling contractors on trips per section and non-productive time. A team that reads directional tendency well holds the plan without corrective runs. The course rests on beam-column BHA modelling, side force and bit tilt analysis, and fatigue accounting on drill collars and heavy-weight pipe.
Who Gains Most from Bottom Hole Assembly Design
- Engineers who write BHA proposals and drilling parameter roadmaps for each hole section
- Rig-site supervisors who approve make-up, stabiliser gauge and run decisions
- Directional drillers who set steering plans and survey correction actions
- Drilling tool specialists who inspect collars, stabilisers and connections between runs
- Well planners who judge whether a trajectory is drillable with a given assembly
An operator or contractor crew that sends its office engineer and its rig supervisor together gains most.
Bottom Hole Assembly Design Capabilities
Participants predict how an assembly will steer, bend and wear before it is run.
- Calculate stabiliser placement for build, drop and hold tendency — section well plan approval
- Assess bit and BHA matching for side cutting and walk — bit selection meetings
- Weigh motor, rotary steerable and rotary assemblies against dogleg needs — directional plan sign-off
- Specify drill collar size and weight on bit distribution — buckling and neutral point decisions
- Apply cumulative fatigue tracking to collars and connections — tool inspection intervals
- Communicate BHA run results and failure causes — the next section's assembly change
Key Bottom Hole Assembly Design Terms
- Bottom hole assembly (BHA) — the lower drillstring between the bit and the drill pipe, including collars, stabilisers, motors and measurement tools.
- Directional tendency — the build, drop or turn an assembly produces under given weight and speed.
- Side force at the bit — the lateral load the bit applies to the borehole wall.
- Pendulum assembly — a BHA with a stabiliser placed above the bit so gravity pulls the bit toward vertical and drops angle.
- Neutral point — the point in the drillstring where axial stress changes from compression to tension under applied weight on bit.
- Bending stress ratio — the ratio of box to pin section stiffness used to judge collar connection fatigue life.
Bottom Hole Assembly Design Day by Day
Day 1: Assembly Components and Well Path Demands
- Drill Collar, HWDP and Jar Placement — Weight Delivery Without Buckling
- Stabiliser Types and Gauge Condition — Hole Quality and Torque Limits
- Well Profile Build, Turn and Hold Segments — Assembly Requirements Per Section
- Dogleg Severity and Casing Run Limits — Acceptable Steering Envelopes
- Offset Well Run Records — Lessons That Set the First Assembly
Day 2: Predicting Directional Tendency
- Beam-Column Assembly Modelling — Predicted Build or Drop Rate
- Fulcrum, Pendulum and Packed Hole Layouts — Choosing the Section Assembly
- Bit Side Force and Tilt Calculation — Expected Inclination Response
- Formation Dip and Anisotropy Effects — Walk and Turn Corrections
- Weight on Bit and Rotary Speed Sensitivity — Parameter Windows for Tendency
Day 3: Bits, Motors and Steering Systems
- PDC and Roller Cone Side Cutting Behaviour — Bit and BHA Matching
- Bent Housing Motor Setting and Slide Ratio — Steering Efficiency Choices
- Push-the-Bit and Point-the-Bit Rotary Steerables — System Selection by Profile
- Survey Spacing and Projection to Bit — Steering Correction Timing
- Hole Cleaning With Steering Assemblies — Cuttings Bed Risk in Slides
Day 4: Fatigue, Failure and Run Reliability
- Cumulative Rotating Hours and Fatigue Logs — Collar Retirement Decisions
- Connection Bending Stress Ratio Checks — Make-Up Torque and Thread Selection
- Twist-Off and Washout Investigation — Root Causes Behind Lost Runs
- Shock and Whirl Signatures Near the Bit — Stabiliser Spacing Revisions
- Inspection Categories for BHA Components — Rerun or Replace Judgements
Day 5: Practising the BHA Selection and Tendency Sheet
- Tendency Model for a Build Section — Applying Day 2 Layout Choices
- Bit and Steering System Pairing — Applying Day 3 Selection Rules
- Fatigue Budget for the Planned Run — Applying Day 4 Inspection Limits
- Run Review Format for Rig and Office — Sharing Assembly Performance
- BHA Selection and Tendency Sheet — Final Section Assembly Proposal
Applying Bottom Hole Assembly Design After the Course
- Rebuild the assembly proposal for the next hole section with a beam-column tendency check.
- Start a fatigue log for collars and stabilisers on the rig and set inspection triggers by rotating hours.
Bottom Hole Assembly Design Questions (FAQ)
What is bottom hole assembly design and why does it matter now?
Bottom hole assembly design is the choice and spacing of collars, stabilisers, bits and steering tools to control well path and reliability. It matters now because complex profiles and expensive steering tools make each failed or off-plan run very costly.
Which roles gain most from bottom hole assembly design training?
Drilling engineers and rig-site supervisors gain most, together with directional drillers and tool specialists. It suits those who write assembly proposals or investigate failed runs on land and offshore wells.
How does this bottom hole assembly design course differ from a vibration or casing design course?
This course centres on predicting directional tendency and selecting the assembly for a section. A vibration course focuses on penetration rate and dynamics, and a casing course on tubular loads.
What do you bring back from bottom hole assembly design training?
You bring back a completed assembly sheet for a real or sample section, with tendency predictions, bit and steering choices and a fatigue budget.
Bottom Hole Assembly Design: The Way Forward
The BHA Selection and Tendency Sheet first informs the assembly choice for the next build or tangent section. Drilling engineers use it to draft the proposal, and rig supervisors use it on the floor. After its first run, compare predicted and actual build rates and recalibrate the model before the following section.
Find more Petroleum Engineering & Oil and Gas Operations Courses by city
Questions about dates, fees and booking
When does this course next run?
The next session runs 30 November – 4 December 2026 in London. It is one of 25 dates scheduled up to November 2027.
Where is this course held?
In a classroom in 24 cities: London, Singapore, Rome, Dar es Salaam, Amsterdam, Manama, Munich, Sharm El-Sheikh, and more. It is also scheduled as live online sessions.
Can I attend this course online?
Yes. One date is scheduled as a live online session: 26 – 30 September 2027, from 2,900 £ per participant.
How long is the course?
1 Week. Each date shows its start and end dates.
How much does the course cost?
Fees per participant run from 4,000 £ (Cairo) to 9,500 £ (New York) in a classroom, and from 2,900 £ live online. Each date shows its own fee.
Is there a brochure for this course?
How do I book a place?
Choose a date above and select Register, or send us an enquiry.
Can this course be run for our team?
Yes. Tell us the number of participants and your preferred dates and city through our training request form.