Skip to content

Control Valve Sizing and Selection Training Course

Flow coefficient, cavitation, noise and actuator calculations for process and design engineers who specify valves for new and debottlenecked duties.

This 1-week course has 25 dates from November 2026 to November 2027 in 24 cities and live online. The next session runs 22 – 26 November 2026 in Dubai. Fees per participant run from 4,000 £ (Cairo) to 9,500 £ (New York) in a classroom, and from 2,900 £ live online.

See dates and book Download brochure (PDF) Training for your team

Duration
1 Week
Next start
Dubai
Scheduled dates
25
Classroom cities
24
Classroom fee from
4,000 £
Online fee from
2,900 £

When and where does this course run?

Showing 1–20 of 25 dates

November 2026

December 2026

January 2027

February 2027

March 2027

April 2027

May 2027

June 2027

July 2027

August 2027

October 2027

Can’t find a suitable date? Tell us what you need.

What does this course cover?

Control Valve Sizing and Selection is a 1-week training course for process and design engineers who calculate flow coefficients, screen duties for cavitation and noise, and choose actuators, and who leave with a control valve specification datasheet for one demanding duty. An oversized or wrongly trimmed valve undermines throughput, energy use and equipment life from the day it is commissioned. Jupiter Prime Training delivers this Control Valve Sizing and Selection course.

Why Control Valve Sizing and Selection Matters Now

Plants are pushing wider turndown as feedstocks and demand swing, so a valve must throttle well at both minimum and maximum flow. Tighter energy targets make every unnecessary bar of pressure drop visible to operations leaders. Projects also buy more valves through packaged equipment vendors, which leaves owner engineers checking datasheets they did not write. A well-sized valve gives stable loops, quiet piping and long trim life; a poorly sized one brings flashing damage, vibration and early replacement. The course rests on the internationally recognised sizing equations for liquids and gases and on recognised noise prediction methods, described in general terms.

Who Gains Most from Control Valve Sizing and Selection

  • Engineers who write process datasheets and set design flow cases for new valves
  • Designers who select body style, trim and pressure class for piping specifications
  • Engineers who review vendor sizing calculations during bid evaluation
  • Staff responsible for debottlenecking studies where existing valves limit capacity
  • Engineers who plan installation, straight-run and commissioning checks for new valves

A project or plant engineering group that sends its process and piping engineers together gains most.

Control Valve Sizing and Selection Capabilities

Participants turn a flow case into a defensible valve choice.

  • Calculate required flow coefficients for liquid, gas and two-phase cases — the body size decision
  • Assess choked flow, flashing and cavitation risk from pressure recovery — trim and material choice
  • Weigh aerodynamic and hydrodynamic noise against limits — piping and occupational health stakeholders
  • Specify actuator thrust or torque with suitable margin — fail action and shut-off duty
  • Design installation details for straight runs, reducers and access — layout and maintenance teams
  • Test the installed valve during commissioning — handover to operations

Key Control Valve Sizing and Selection Terms

  • Flow coefficient (Cv or Kv) — the flow a valve passes at a reference pressure drop, used to size the body and trim.
  • Choked flow — the condition where further drop in outlet pressure no longer increases flow through the valve.
  • Pressure recovery factor — a ratio describing how much pressure a valve regains downstream of its vena contracta.
  • Rangeability — the ratio of largest to smallest flow a valve controls with acceptable accuracy.
  • Installed characteristic — the real relation between valve travel and flow once piping and pump curves are included.
  • Anti-cavitation trim — staged or drilled internals that split pressure drop to keep local pressure above vapour pressure.

Control Valve Sizing and Selection Day by Day

Day 1: Process Conditions and Flow Cases

  • Minimum, Normal and Maximum Flow Cases — Setting the Sizing Envelope
  • Pump and System Curves — Allocating Pressure Drop to the Valve
  • Fluid Property Sheets — Capturing Density, Vapour Pressure and Viscosity
  • Turndown and Rangeability Targets — Matching Valve Style to Duty
  • Process Datasheet Review — Spotting Missing or Conflicting Conditions

Day 2: Sizing Calculations

  • Liquid Sizing Equations — Calculating Required Cv With Correction Factors
  • Gas and Steam Sizing Equations — Handling Expansion and Compressibility
  • Viscous and Two-Phase Corrections — Adjusting Size for Difficult Fluids
  • Reducer and Piping Geometry Factors — Correcting for Line-Size Mismatch
  • Installed Characteristic Plots — Choosing Linear or Equal Percentage Trim

Day 3: Cavitation, Flashing and Noise

  • Cavitation Index Screening — Predicting Onset and Damage Risk
  • Flashing Service Design — Selecting Body Form and Hardened Materials
  • Multi-Stage and Drilled-Cage Trim — Splitting Pressure Drop for Severe Duty
  • Aerodynamic Noise Prediction — Comparing Sound Level With Site Limits
  • Diffusers and Silencers — Treating Noise at Source or Downstream

Day 4: Actuator Selection and Installation

  • Actuator Thrust and Torque Calculations — Sizing for Shut-Off and Stroke Speed
  • Fail-Safe Action Choice — Aligning Valve Position With Process Hazard
  • Body Style Trade-Offs — Globe, Rotary and Angle Valves by Duty
  • Straight-Run and Access Layout — Placing Valves for Accurate Control
  • Commissioning Stroke and Loop Checks — Proving the Valve Before Start-Up

Day 5: Practising the Control Valve Specification Datasheet

  • Vendor Bid Comparison — Applying Sizing Checks to Competing Offers
  • Severe Service Case Study — Applying Cavitation and Noise Screening
  • Debottlenecking Exercise — Applying Installed Characteristic to an Existing Valve
  • Selection Rationale Note — Recording Assumptions Behind Each Choice
  • Control Valve Specification Datasheet — Completing Sizing and Selection for One Duty

Applying Control Valve Sizing and Selection After the Course

  • Recheck the sizing of three valves that run near closed or fully open, using all three flow cases
  • Add cavitation index and predicted noise fields to the site valve datasheet template

Control Valve Sizing and Selection Questions (FAQ)

What is control valve sizing and selection and why does it matter now?

It is the calculation of flow coefficients and the choice of body, trim and actuator for a process duty. It matters now because wider turndown, energy targets and vendor-supplied packages all expose poorly sized valves.

Which roles gain most from control valve sizing and selection training?

Process and design engineers gain most, especially those who write datasheets, review vendor calculations or study capacity limits caused by existing valves.

How does control valve sizing and selection differ from a valve maintenance course?

This course decides what valve to buy and how to install it. A maintenance course repairs, repacks and recalibrates valves already in service, working at the bench rather than on calculations.

What do you bring back from control valve sizing and selection training?

You bring back a control valve specification datasheet for one demanding duty, with flow cases, calculated Cv, cavitation and noise checks, actuator sizing and a selection rationale.

Control Valve Sizing and Selection: The Way Forward

The control valve specification datasheet first informs the purchase decision for one demanding duty. Process engineers, piping designers and procurement staff use it to compare vendor offers on equal terms. After commissioning, revisit the assumed flow cases against measured operation, because real turndown often differs from design and shapes the next specification.

Questions about dates, fees and booking

When does this course next run?

The next session runs 22 – 26 November 2026 in Dubai. It is one of 25 dates scheduled up to November 2027.

Where is this course held?

In a classroom in 24 cities: Dubai, Manama, Paris, London, Madrid, Amman, Muscat, Doha, and more. It is also scheduled as live online sessions.

Can I attend this course online?

Yes. One date is scheduled as a live online session: 27 – 31 December 2026, from 2,900 £ per participant.

How long is the course?

1 Week. Each date shows its start and end dates.

How much does the course cost?

Fees per participant run from 4,000 £ (Cairo) to 9,500 £ (New York) in a classroom, and from 2,900 £ live online. Each date shows its own fee.

Is there a brochure for this course?

How do I book a place?

Choose a date above and select Register, or send us an enquiry.

Can this course be run for our team?

Yes. Tell us the number of participants and your preferred dates and city through our training request form.

More ways to train