Skip to content

Pump and Compressor Maintenance Task Improvement Training Course

Turn failure modes, reliability data and root cause findings into sharper pump and compressor tasks, for rotating equipment engineers and supervisors.

This 1-week course has 25 dates from November 2026 to November 2027 in 24 cities and live online. The next session runs 29 November – 3 December 2026 in Cairo. Fees per participant run from 4,000 £ (Cairo) to 9,500 £ (New York) in a classroom, and from 2,900 £ live online.

See dates and book Download brochure (PDF) Training for your team

Duration
1 Week
Next start
Cairo
Scheduled dates
25
Classroom cities
24
Classroom fee from
4,000 £
Online fee from
2,900 £

When and where does this course run?

Showing 1–20 of 25 dates

November 2026

December 2026

January 2027

February 2027

March 2027

April 2027

May 2027

June 2027

July 2027

August 2027

September 2027

October 2027

Can’t find a suitable date? Tell us what you need.

What does this course cover?

Pump and Compressor Maintenance Task Improvement is a 1-week training course for rotating equipment engineers and maintenance supervisors who build a task revision register for their critical machines. Ageing pump trains, leaner crews and rising energy costs now make every wasted or missing maintenance task expensive. Jupiter Prime Training presents Pump and Compressor Maintenance Task Improvement as a practical route from failure evidence to better routines.

Why Pump and Compressor Maintenance Task Improvement Matters Now

Three pressures shape this subject. Operations teams expect higher availability from fewer spare machines, energy managers watch the power drawn by inefficient pumps and compressors, and experienced fitters are retiring before their judgement is written into job plans. Plants that tune their task lists see fewer seal leaks and trips; plants that keep inherited routines spend hours on checks that find nothing. The course rests on Failure Modes and Effects Analysis (FMEA), Reliability-Centred Maintenance (RCM) logic and Root Cause Analysis (RCA), applied at the level of the individual task.

Who Gains Most from Pump and Compressor Maintenance Task Improvement

  • Engineers responsible for the reliability of centrifugal pumps, screw compressors and reciprocating compressors
  • Supervisors who plan and assign mechanical jobs on rotating machines
  • Planners who write and maintain job plans in the maintenance system
  • Condition monitoring specialists who set vibration and oil analysis routes
  • Technical leads who chair failure investigations on machine trains

A maintenance department gains most when its engineer, planner and supervisor attend together and revise one shared machine list.

Pump and Compressor Maintenance Task Improvement Capabilities

Participants turn failure histories into task changes a planner can load.

  • Assess the dominant failure modes of each machine type — choice of tasks worth keeping
  • Calculate task intervals from failure records and inspection results — planner scheduling
  • Specify alignment, balancing and lubrication acceptance limits — craft quality on the shop floor
  • Apply root cause findings to rewrite or remove a routine — investigation follow-through
  • Weigh condition-based checks against fixed-time overhauls — budget and downtime trade-offs
  • Communicate task changes with clear justification — operations and asset owners

Key Pump and Compressor Maintenance Task Improvement Terms

  • Failure mode — the specific way a component stops doing its job, such as seal face wear or bearing fatigue.
  • P-F interval — the time between the first detectable sign of a failure and the point of functional failure.
  • Soft foot — a machine foot that does not sit flat on its base, distorting the casing when bolts are tightened.
  • Residual unbalance — the unbalance left in a rotor after balancing, judged against a permitted tolerance grade.
  • Surge — unstable flow reversal in a dynamic compressor when operating flow falls below its stable limit.
  • Task effectiveness — the share of executions of a maintenance task that detect or prevent the failure it targets.

Pump and Compressor Maintenance Task Improvement Day by Day

Day 1: Machine Context and Task Baseline

  • Machine Criticality Ranking — Which Trains Receive Task Review First
  • Existing Job Plan Audit — Tasks That Duplicate, Overlap or Lack Purpose
  • Work Order History Extraction — Reliable Evidence for Task Decisions
  • Operating Envelope Review — Effect of Duty Point on Failure Exposure
  • Energy Use Profiling — Linking Efficiency Loss to Maintenance Neglect

Day 2: Failure Modes of Pumps and Compressors

  • Mechanical Seal Failure Patterns — Flush Plans and Seal Selection Choices
  • Cavitation and Recirculation Damage — Suction Conditions and Operating Limits
  • Compressor Valve and Ring Wear — Reciprocating Overhaul Timing
  • Surge and Fouling in Dynamic Compressors — Control and Washing Routines
  • FMEA Worksheet for a Machine Train — Ranking Modes for Task Coverage

Day 3: Precision Care: Alignment, Balancing and Bearings

  • Laser Shaft Alignment and Soft Foot Correction — Coupling and Bearing Life
  • Field Balancing With Tolerance Grades — Acceptance After Rotor Repair
  • Bearing Lubrication Practice — Grease Quantity, Oil Level and Contamination
  • Pipe Strain Checks — Casing Distortion and Repeat Misalignment
  • Precision Acceptance Sheets — Quality Limits Written Into Job Plans

Day 4: Reliability Data and Root Cause Evidence

  • Mean Time Between Failures Trending — Spotting Machines That Need Attention
  • Vibration and Oil Analysis Findings — Condition Tasks and Alarm Limits
  • Root Cause Analysis Using Five Whys and Fault Trees — Defect Elimination
  • RCM Decision Logic — Choosing Condition, Time or Run-to-Failure
  • Interval Setting From P-F Evidence — Inspection Frequency Choices

Day 5: Practising the Task Revision Register

  • Criticality and FMEA Results Applied — Selecting the Pilot Machine Train
  • Precision Limits Applied — Rewriting Alignment and Lubrication Steps
  • Root Cause Findings Applied — Removing Tasks That Add No Protection
  • Task Change Justification Note — Securing Operations and Planner Agreement
  • Task Revision Register — Completing Changes, Intervals and Owners

Applying Pump and Compressor Maintenance Task Improvement After the Course

  • Run an FMEA review of one critical pump or compressor train and replace low-value checks with condition tasks.
  • Add alignment and balancing acceptance limits to the job plans of the next three scheduled overhauls.

Pump and Compressor Maintenance Task Improvement Questions (FAQ)

What is Pump and Compressor Maintenance Task Improvement and why does it matter now?

It is the practice of revising maintenance tasks on pumps and compressors using failure modes, reliability data and root cause findings. It matters because leaner crews cannot afford routines that miss real failures.

Which roles gain most from Pump and Compressor Maintenance Task Improvement?

Rotating equipment engineers and maintenance supervisors gain most. Planners and condition monitoring specialists also benefit.

How does Pump and Compressor Maintenance Task Improvement differ from a longer reliability engineering course?

It focuses on improving individual tasks on pumps and compressors within one week. A longer reliability engineering course covers life data modelling and availability across many machine types.

What do you bring back from Pump and Compressor Maintenance Task Improvement?

You bring back a revised set of tasks for one critical machine train, with intervals, precision limits and owners, plus a method to repeat on other machines.

Pump and Compressor Maintenance Task Improvement: The Way Forward

The task revision register is the starting point. Its first use is to decide which routines on the pilot machine train are kept, changed or removed. Planners load it and engineers track its effect on failures. After the first overhaul cycle, revisit the intervals against the new condition findings and extend the review to the next train.

Questions about dates, fees and booking

When does this course next run?

The next session runs 29 November – 3 December 2026 in Cairo. It is one of 25 dates scheduled up to November 2027.

Where is this course held?

In a classroom in 24 cities: Cairo, Casablanca, Sharm El-Sheikh, Amsterdam, London, Paris, Milan, New York, and more. It is also scheduled as live online sessions.

Can I attend this course online?

Yes. One date is scheduled as a live online session: 21 – 25 November 2027, from 2,900 £ per participant.

How long is the course?

1 Week. Each date shows its start and end dates.

How much does the course cost?

Fees per participant run from 4,000 £ (Cairo) to 9,500 £ (New York) in a classroom, and from 2,900 £ live online. Each date shows its own fee.

Is there a brochure for this course?

How do I book a place?

Choose a date above and select Register, or send us an enquiry.

Can this course be run for our team?

Yes. Tell us the number of participants and your preferred dates and city through our training request form.

More ways to train