Refinery Fired Heater Efficiency and Reliability Training Course
Practical heater skills for operators and engineers who want lower fuel use, steadier combustion and longer tube run length between decoking.
This 1-week course has 25 dates from December 2026 to November 2027 in 24 cities and live online. The next session runs 7 – 11 December 2026 in Milan. Fees per participant run from 4,000 £ (Cairo) to 9,500 £ (New York) in a classroom, and from 2,900 £ live online.
See dates and book Download brochure (PDF) Training for your team
- Duration
- 1 Week
- Next start
- Milan
- Scheduled dates
- 25
- Classroom cities
- 24
- Classroom fee from
- 4,000 £
- Online fee from
- 2,900 £
What does this course cover?
Refinery Fired Heater Efficiency and Reliability is a 1-week training course for heater operators, process engineers and reliability engineers, built around a heater run-length improvement plan for one furnace on their own site. Fired heaters burn much of a refinery's fuel and set the pace of crude, vacuum, reformer and coker units, so small losses in combustion or tube condition quickly erode margin and uptime. The course is delivered by Jupiter Prime Training.
Why Refinery Fired Heater Efficiency and Reliability Matters Now
Three pressures meet at the heater firebox today. Fuel cost and emissions reporting push sites to burn less gas per unit of duty, longer turnaround intervals stretch tube and burner life, and fewer experienced board operators means combustion judgement must be written down. Good control of excess air, draft and tube metal temperature brings fuel savings and predictable run length; poor control brings tube ruptures, unplanned decoking and lost throughput. The course rests on heat balance methods, combustion stoichiometry and damage-mechanism thinking used across the process industries.
Who Gains Most from Refinery Fired Heater Efficiency and Reliability
- Board and field operators who set burner registers, stack dampers and fuel gas pressure on each shift
- Process engineers responsible for heater duty, coil outlet temperature and fuel consumption targets
- Reliability engineers who track tube metal temperature, creep life and coking trends
- Maintenance planners who schedule burner cleaning, refractory repair and decoking windows
- Inspection specialists who judge tube thickness, bulging and oxidation at turnaround
A unit crew sending an operator and both engineers together gains most.
Refinery Fired Heater Efficiency and Reliability Capabilities
Participants leave able to read a heater as one thermal system, from burner tip to stack, and defend each adjustment with logged data.
- Calculate heater thermal efficiency from flue gas oxygen and stack temperature — fuel budget and emissions reporting
- Specify excess air and draft targets for each firing rate — shift operating envelopes
- Assess tube metal temperature trends against design limits — run length and creep life decisions
- Apply coking indicators to schedule spalling or pigging — turnaround planning
- Test burner condition through flame pattern and tip inspection — maintenance priorities
- Build a heater run-length improvement case — unit manager and operations leadership
Key Refinery Fired Heater Efficiency and Reliability Terms
- Excess air — combustion air supplied above the stoichiometric amount, measured as oxygen in the flue gas.
- Draft — the pressure below atmosphere inside the firebox that draws combustion air in and pushes flue gas out.
- Tube metal temperature — the measured or estimated outer wall temperature of a process coil, the main limit on heater firing.
- Coking — the deposit of carbon inside heater tubes that raises wall temperature and pressure drop.
- Bridgewall temperature — flue gas temperature leaving the radiant section, a guide to firebox heat release.
- Flame impingement — flame contact with tubes that causes local overheating, oxidation and early failure.
Refinery Fired Heater Efficiency and Reliability Day by Day
Day 1: Heater Duty and Thermal Balance
- Radiant and Convection Section Heat Duty Split — Where Absorbed Heat Is Lost
- Fuel Gas and Fuel Oil Heating Values — Firing Rate Calculations
- Flue Gas Heat Loss Method — Thermal Efficiency Baseline for Each Heater
- Coil Outlet Temperature Control Loops — Stability Versus Fuel Use
- Heater Data Historian Tags — Which Readings Operators Trust
Day 2: Combustion Air and Draft Control
- Combustion Stoichiometry and Oxygen Analysers — Setting Excess Air Targets
- Arch Draft Measurement and Stack Damper Use — Firebox Pressure Envelope
- Natural, Forced and Balanced Draft Arrangements — Control Strategy Choices
- Carbon Monoxide Monitoring and Oxygen Trim — Safe Low Air Operation
- Air Preheater and Tramp Air Leaks — Recovering Lost Efficiency
Day 3: Tube Integrity and Coking
- Skin Thermocouples and Infrared Surveys — Tube Metal Temperature Picture
- Creep, Carburisation and Oxidation Mechanisms — Remaining Tube Life Estimates
- Coke Laydown Rate and Pressure Drop Trends — Predicting End of Run
- Steam Air Decoking, Spalling and Pigging — Choosing the Cleaning Route
- Flux Rate and Flame Impingement Checks — Firing Limits by Pass
Day 4: Burners, Refractory and Maintenance
- Burner Tip Fouling and Flame Pattern Inspection — Cleaning Frequency
- Low Emission Burner Tuning — Flame Length and Nitrogen Oxides Trade-Off
- Refractory Hot Spot Thermography — Casing Repair Priorities
- Pass Flow Balancing and Low Flow Trips — Protecting Coils During Upsets
- Heater Safe Light-Off and Purge Sequences — Start-Up Readiness
Day 5: Practising the Heater Run-Length Improvement Plan
- Thermal Efficiency Baseline Review — Selecting the Target Heater
- Excess Air and Draft Envelope Setting — Operating Limits for the Plan
- Tube Temperature and Coking Forecast — Expected Run Length Gain
- Burner and Refractory Action List — Maintenance Window Requests
- Heater Run-Length Improvement Plan — Final Case for Unit Leadership
Applying Refinery Fired Heater Efficiency and Reliability After the Course
- Lead a one-week oxygen and draft survey on one heater.
- Run a tube metal temperature and pressure drop trend review to forecast the next decoking date.
Refinery Fired Heater Efficiency and Reliability Questions (FAQ)
What is refinery fired heater efficiency and reliability, and why does it matter now?
It is the practice of burning less fuel per unit of process duty while keeping tubes, burners and refractory healthy for a full run. Fuel costs and longer turnarounds make both goals urgent.
Which roles gain most from refinery fired heater efficiency and reliability training?
Heater operators, process engineers and reliability engineers gain most. Shared methods let these three groups agree on each firing decision.
How does refinery fired heater efficiency and reliability differ from a refinery energy audit course?
It focuses on one equipment type in depth. An energy audit course surveys a whole site, while this one works inside the firebox on air, draft, tubes and burners.
What do you bring back from refinery fired heater efficiency and reliability training?
You bring back a heater run-length improvement plan for one furnace. It sets air and draft limits, forecasts coking and lists burner actions.
Refinery Fired Heater Efficiency and Reliability: The Way Forward
The heater run-length improvement plan first informs the operating envelope for excess air and draft on the target furnace. Operators use it on shift, process engineers for fuel targets and reliability engineers to time decoking. After its first run, revisit the coking forecast against measured pressure drop and refine the limits for the next heater.
When and where does this course run?
Showing 1–20 of 25 dates
December 2026
January 2027
February 2027
March 2027
April 2027
May 2027
June 2027
July 2027
August 2027
Can’t find a suitable date? Tell us what you need.
Find more Petroleum Engineering & Oil and Gas Operations Courses by city
Questions about dates, fees and booking
When does this course next run?
The next session runs 7 – 11 December 2026 in Milan. It is one of 25 dates scheduled up to November 2027.
Where is this course held?
In a classroom in 24 cities: Milan, Cairo, Madrid, Rome, Munich, Doha, Muscat, London, and more. It is also scheduled as live online sessions.
Can I attend this course online?
Yes. One date is scheduled as a live online session: 29 August – 2 September 2027, from 2,900 £ per participant.
How long is the course?
1 Week. Each date shows its start and end dates.
How much does the course cost?
Fees per participant run from 4,000 £ (Cairo) to 9,500 £ (New York) in a classroom, and from 2,900 £ live online. Each date shows its own fee.
Is there a brochure for this course?
How do I book a place?
Choose a date above and select Register, or send us an enquiry.
Can this course be run for our team?
Yes. Tell us the number of participants and your preferred dates and city through our training request form.