Control Valve Application and Installed Performance Training Course
Sizing and installed-performance training for instrument and process engineers who specify, tune and maintain control valves in real process loops.
This 1-week course has 25 dates from November 2026 to November 2027 in 24 cities and live online. The next session runs 29 November – 3 December 2026 in Abu Dhabi. Fees per participant run from 4,000 £ (Cairo) to 9,500 £ (New York) in a classroom, and from 2,900 £ live online.
See dates and book Download brochure (PDF) Training for your team
- Duration
- 1 Week
- Next start
- Abu Dhabi
- Scheduled dates
- 25
- Classroom cities
- 24
- Classroom fee from
- 4,000 £
- Online fee from
- 2,900 £
When and where does this course run?
Showing 1–20 of 25 dates
November 2026
December 2026
January 2027
February 2027
March 2027
April 2027
May 2027
June 2027
July 2027
August 2027
September 2027
Can’t find a suitable date? Tell us what you need.
What does this course cover?
Control Valve Application and Installed Performance is a 1-week training course for instrument and process engineers who specify, commission and maintain final control elements, and it ends with a control valve application dossier for one critical loop. Valves that look right on a datasheet often hunt or cavitate once installed. Jupiter Prime Training delivers this view of control valves as installed loop components.
Why Control Valve Application and Installed Performance Matters Now
Plants run closer to design limits, digital positioners now report friction and deadband that few teams read, and reliability engineers must cut trim replacements caused by flashing. An organisation that sizes against real pump curves and line losses gains stable loops and longer packing life; one that sizes from a single design point inherits oscillation, noise complaints and repeated shutdowns. The course rests on the international control valve sizing equations and the published guidance on valve noise prediction, described here in general terms.
Who Gains Most from Control Valve Application and Installed Performance
- Instrument engineers who write valve datasheets and approve vendor sizing calculations
- Process engineers who set flow, pressure-drop and turndown requirements for each loop
- Control engineers who tune loops and diagnose oscillation traced to the valve
- Maintenance and reliability engineers who plan trim, packing and actuator overhauls
An operating unit gains most when its instrument, process and maintenance engineers attend together, because installed performance problems sit between their separate responsibilities.
Control Valve Application and Installed Performance Capabilities
Participants judge each valve across its full operating envelope, with actuator and positioner.
- Calculate required flow coefficient at minimum, normal and maximum conditions — datasheet approval
- Specify inherent characteristic from installed gain and pressure-drop ratio — loop stability
- Assess choked flow, cavitation and flashing risk for liquid service — trim and material selection
- Weigh aerodynamic noise and outlet velocity limits for gas service — plant safety and neighbours
- Design actuator thrust and positioner configuration for shut-off and response — commissioning sign-off
- Apply positioner diagnostics to plan overhaul intervals — maintenance planners
Key Control Valve Application and Installed Performance Terms
- Flow coefficient (Cv/Kv) — the flow a valve passes at a reference pressure drop, used to size the body and trim.
- Installed characteristic — the relationship between valve travel and actual flow once line and pump losses are included.
- Pressure-drop ratio — the share of total system pressure drop taken by the valve, which shapes installed gain.
- Choked flow — the condition where further reduction in outlet pressure no longer increases flow through the valve.
- Rangeability — the ratio of maximum to minimum controllable flow a valve delivers within acceptable gain.
- Deadband — the change in controller signal that produces no measurable movement of the valve stem.
Control Valve Application and Installed Performance Day by Day
Day 1: Valves Inside the Process System
- System Curve and Pump Curve Interaction — Pressure Available at the Valve
- Pressure-Drop Ratio Allocation — Trade-Off Between Energy Cost and Controllability
- Body Styles: Globe, Rotary Ball and Butterfly — Matching Geometry to Duty
- Operating Envelope Definition — Minimum, Normal and Maximum Flow Cases
- Loop Failure Histories — Recurring Faults Traced to Valve Application
Day 2: Sizing Across the Operating Envelope
- Liquid Sizing Equations — Required Flow Coefficient at Each Case
- Gas and Steam Sizing with Expansion Factor — Compressible Service Choices
- Piping Geometry Factor for Reducers — Corrected Capacity of Line-Mounted Valves
- Percent Opening Targets — Avoiding Operation Near Seat or Full Travel
- Vendor Sizing Report Cross-Check — Accepting or Challenging Calculations
Day 3: Characteristics, Cavitation and Noise
- Linear Versus Equal-Percentage Trim — Installed Gain Across the Range
- Liquid Pressure Recovery Factor — Onset of Cavitation and Flashing
- Anti-Cavitation and Multi-Stage Trim — Erosion Control in Severe Service
- Aerodynamic Noise Prediction — Limits for Gas Letdown Stations
- Outlet Velocity and Trim Material — Wear Life in Slurry and Flashing Duty
Day 4: Actuators, Positioners and Diagnostics
- Actuator Thrust and Torque Calculation — Shut-Off Class and Unbalanced Forces
- Fail-Safe Action and Spring Range — Behaviour on Air or Signal Loss
- Digital Positioner Configuration — Response Speed Versus Overshoot
- Step Response and Valve Signature Tests — Friction and Deadband Evidence
- Packing, Seat Leakage and Overhaul Triggers — Condition-Based Maintenance Intervals
Day 5: Practising the Control Valve Application Dossier
- Envelope Sizing of a Participant Loop — Applying Day Two Equations
- Installed Gain Plot for the Chosen Trim — Confirming Day Three Selection
- Actuator and Positioner Specification — Applying Day Four Thrust Checks
- Peer Challenge of Sizing Assumptions — Defending Choices to Process Colleagues
- Control Valve Application Dossier — Datasheet, Gain Plot and Maintenance Triggers
Applying Control Valve Application and Installed Performance After the Course
- Re-run the sizing of one oscillating loop at minimum and maximum flow and compare the result with its installed trim.
- Collect valve signature and deadband data from digital positioners on five critical valves and set overhaul triggers.
Control Valve Application and Installed Performance Questions (FAQ)
What is control valve application and installed performance, and why does it matter now?
It is the practice of sizing and specifying a control valve for how it behaves in the real line, not on paper. Tighter margins make that view decisive.
Which roles gain most from control valve application and installed performance?
Instrument and process engineers gain most, followed by control, reliability and commissioning engineers. Each owns part of the valve decision.
How does control valve application and installed performance differ from a general valve maintenance course?
It starts with process conditions and loop behaviour rather than bench repair. You size, select trim and specify actuators first, then link positioner diagnostics to maintenance, unlike a dismantling and reassembly course.
What do you bring back from control valve application and installed performance?
You bring back a sizing and specification record for one real loop from your plant. It holds envelope calculations, a gain plot and diagnostic triggers.
Control Valve Application and Installed Performance: The Way Forward
The control valve application dossier first informs whether an existing valve should be re-trimmed, resized or left alone. Instrument engineers use it to approve datasheets, process engineers to set pressure-drop allowances and planners to schedule overhauls. After its first use, revisit the minimum-flow case: it is where most installed performance problems hide and where pump or line changes shift the answer.
Find more Maintenance, Reliability & Asset Integrity Training Courses by city
Questions about dates, fees and booking
When does this course next run?
The next session runs 29 November – 3 December 2026 in Abu Dhabi. It is one of 25 dates scheduled up to November 2027.
Where is this course held?
In a classroom in 24 cities: Abu Dhabi, Paris, Geneva, Amsterdam, Rome, Sharm El-Sheikh, Kuala Lumpur, Casablanca, and more. It is also scheduled as live online sessions.
Can I attend this course online?
Yes. One date is scheduled as a live online session: 4 – 8 April 2027, from 2,900 £ per participant.
How long is the course?
1 Week. Each date shows its start and end dates.
How much does the course cost?
Fees per participant run from 4,000 £ (Cairo) to 9,500 £ (New York) in a classroom, and from 2,900 £ live online. Each date shows its own fee.
Is there a brochure for this course?
How do I book a place?
Choose a date above and select Register, or send us an enquiry.
Can this course be run for our team?
Yes. Tell us the number of participants and your preferred dates and city through our training request form.